Ademco Vista-15P v1 Program Sheet

ï»¿ Ademco Vista-15P v1 Program Sheet

Ademco Vista-15P v1 Program Sheet

Version Info Sticker on main chip

Enter Program 1. 4112 + 8 + 0 + 0 (Display should show 00)

2. Power down then back up and press * and # within 1 minute

Move to Location * + Location

View Location # + Location (Display will read off one digit at a time)

Exit Program 1. *98 exits and does not allow re-entry to programming without cycling power and pressing * and #

2. *99 exits and does allow re-entry by Installer Code + 8 + 00

Programming can be re-entered up to 1 minute after exiting with * and # (# + 0 disables this feature)

Default Panel *97

Compatibility

Power Ratings 600ma Aux output

2A Siren output

Device Address 00 5881 L/M/H Receiver or Receiver in 6128RF/6150RF Keypads

03 IP Internet or GSM Long Range Radio

04 4286 Voice Module

07 4219/4229 Zone Expander 1 (Zones 09 to 16, this address is not available if zone doubling)

08 4219/4229 Zone Expander 2 (Zones 17 to 24)

12 to 13 4204 Relay Expander (1st must be address 12)

16 to 23 6128/6139/6150/6160 Keypads (1st keypad must use address 16)

28 5800TM Module for Bi-Direction Keyfobs (cut Red W1 jumper)

Keypad Address (6128/6139/6150/6160 keypads)

Remove power from keypad then power back up
Hold 1 & 3 for 3 seconds, "ADDR = XX" or "XX" should appear (XX = current address)
Within 10 seconds enter 00 to erase old address then enter new address (16 to 23)
Press * to save and exit

(6150RF keypads)

Power keypad down then back up or remove backplate
Within 30 seconds hold 1 & 3 for 3 seconds until flashing " - - 0 0"
Press 1 and "cA XX" should appear (XX = current address)
Press 16 then * to exit back to flashing " -- 0 0"
Press * to exit

Addressing Tips 1. Connect 6160 or 6139 Alpha keypad to the panel, change the address to 23

2. Enter programming with 6150RF keypad, enter 10 in location *196

3. Exit programming and the 6139/6160 keypad will begin working, program rest of panel

4. When finished use 6150RF to go to location *196

5. Enter 00 to erase Alpha keypad from system and exit programming

(The 6160/6139 saves address settings so it can be used to program future Vista-15P's)

Sniffer Test (Tests wireless sensors)

Installer Code + # + 3
Keypad displays all wireless sensors, faulting sensor removes it from list
Exit with Installer Code + 1 (OFF)

Go-No Go Test (Verifies adequate RF by reducing receiver signal strength by 50%)

Installer Code + # + 4
a. Siren sounds

b. Panel may send walk test signal (If test signal was programmed)

c. "dd" appears on screen

d. Keypad will beep every 15 seconds

Fault sensor, keypad should beep 3 times and display zone number,

if no beeps sound reorient or move sensor a few inches and try again

Exit with Installer Code + 1 (OFF)

Hex Program Hex A = # + 10 B = # + 11 C = # + 12 D = # + 13 E = # + 14 F = # + 15

20 Installer Code I _ 4 _I _ 1 _I _ 1 _I _ 2 _I
21 Quick Arm Enable I _ 1 _I 0 = Disable

= Enable

22 RF Jam Detect I _ 0 _I 0 = Disable

= RF Jam Enabled

23 Quick Forced Bypass Enable I _ 0 _I 0 = Disable

= Quick Bypass User Code + 6 + # Enabled

24 RF House Code I _ 0 _I _ 0 _I 00 = Disabled, 01 to 31
26 Chime by Zone I _ 0 _I 0 = Disable

= Enable zone to chime in Zone List 3)

27 X-10 House Code I _ 0 _I 0 = A 1 = B 2 = C 3 = D 4 = E 5 = F

= G 7 = H 8 = I 9 = J #10 = K #11 = L

#12 = M #13 = N #14 = O #15 = P

28 4285 Voice Module Access Code I _ 0 _I _ 0 _I 00 = Disable

st digit = 1 to 9
nd digit = # + 11 = * or # + 12 = #

29 Output to Long Range Radio I _ 0 _I 0 = Disable

= Enable

31 Single Alarm Sounding/Zone I _ 0 _I 0 = Disable

= 1 alarm sound per per zone in an arming period

32 Fire Sounder Timeout I _ 0 _I 0 = Timeout

= No Timeout

33 Alarm Bell Timeout I _ 0 _I 0 = None

= 4 minutes
= 8 minutes
= 12 minutes
= 16 minutes

34 Exit Delay I _ 7 _I _ 0 _I 00 to 99 seconds
35 Zone Type 01 Entry Delay I _ 3 _I _ 0 _I 00 to 99 seconds
36 Zone Type 02 Entry Delay I _ 4 _I _ 5 _I 00 to 99 seconds
37 Audible Exit Warning I _ 1 _I 0 = Disable

= Enable

38 Confirm Arming Ding I _ 0 _I 0 = Disable

= 1/2 second siren after exit delay expires
= 1/2 second siren after RF arm command

39 Power Up in Previous State I _ 0 _I 0 = Disable

= Enable

40 PABX Access Code (6 digits) I _ _I _ _I _ _I _ _I _ _I _ _I (If 9 is needed to dial add here)
41 Primary Phone (20 digits) I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I

End Phone with * # + 11 = * # + 12 = # # + 13 = 2.5 second pause

42 Secondary Phone (20 digits) I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I
43 Primary Account I _ _I _ _I _ _I _ _I (Last 4 of Account)

(Hex B = #+11 C = #+12 D = #+13 E = #+14 F = #+15)

44 Secondary Account I _ _I _ _I _ _I _ _I
47 Phone System Select I _ 1 _I 0 = Pulse Dial

= DTMF Dial
= Pulse Dial, CS on Watts Line
= DTMF Dial, CS on Watts Line

48 Report Format I _ 7 _I Primary 0 = 3/1, 4/1 Ademco L/S Standard

I _ 7 _I Secondary 1 = 3/1, 4/1 Radionics Standard

2 = 4/2 Ademco L/S Standard

3 = 4/2 Radionics Standard

6 = 4/2 Ademco Express

7 = Contact ID

8 = 3/1, 4/1 Ademco L/S Expanded

9 = 3/1, 4/1 Radionics Expanded

49 Split/Dual Reporting I _ 0 _I

To Primary Phone To Secondary Phone

0 = All Reports Backup Only

= Alarms, Restore, Cancel All Other Reports
= All Reports except Open/Close, Test Open/Close, Test
= Alarms, Restore, Cancel All Reports
= All Reports except Open/Close, Test All Reports
= All Reports (Dual Reporting) All Reports

(For pager programming go to *160 - *171)

50 15 Second Dial Delay I _ 0 _I 0 = Disable

= Enable

53 Sescoa/Radionics I _ 0 _I 0 = Radionics

= Sescoa

54 Dynamic Signaling Delay I _ 0 _I 0 = No Delay

to F x15 seconds (1 to 225 seconds)

If *54 is set at 0 then system will send on both the landline and radio/cellular/internet backup

If *54 is set at 2 and *55 is set at 0 then panel will send by landline and if it cannot connect

within 30 seconds it will also send by radio/cellular/internet backup

For radio/cellular only accounts set *54 to F and *55 to 1 to prevent signals using landline

55 Dynamic Signaling Priority I _ 0 _I 0 = Primary Dialer First

= Long Range Radio First

56 Zone Programming (6139 or 6160 Alpha Keypad required here)

1. Press 1 here to allow confirming sensor after serial number input

2. Enter Zone to program (01 to 99) (* for next, # for previous menu)

Hardwire Sensors Zone 01 to 06

2-wire Smokes Zone 01 only

4-wire Smokes Zone 02 to 06 (Requires 4204/4229 Relay)

4219/4229 Zone Expander Zone 10 to 17

Keyfobs Zone 49 to 56

Wireless Zone 9 to 34 (Depends on receiver capacity)

Duress Zone 92

Fire Panic Zone 95

Medical Panic Zone 96

Police Panic Zone 99

3. This shows summary of current Zone programming (* for next, # for previous menu)

4. Enter Zone Type (* for next, # for previous menu)

00 = Zone Disabled/Deleted 12 = Monitor Zone (non Burg sends E150)

= Delay Zone 14 = 24 Hr Carbon Monoxide
= Secondary Delay Zone 16 = 24 Hr Fire w/ Verification
= Perimeter/Instant 20 = Arm-Stay (RF only)
= Interior Follower/Motions 21 = Arm-Away (RF only)
= Trouble by Day/Alarm by Night 22 = Disarm (RF only)

To delete Zone enter 00 06 = 24 Hr Silent/Holdup 23 = No Alarm Response

then * until "Delete Sensor" 07 = 24 Hr Police Panic 24 = Silent Burglary

08 = 24 Hr Aux/Medical 77 = Keyswitch Zone

09 = 24 Hr Supervised Fire 90 = Configurable Zone

10 = Interior with Delay 91 = Configurable Zone

(see locations 182 - 185)

User Assign 1. Exit programming

2. Add a user code to system (03 to 33), many techs use last 4 digits of keyfob serial number

3. Master Code + 8 + User (03 to 33) + # + 4

4. Enter 1st keyfob Zone (Example Zone 53) (Keypad should beep)

5. Enter Report Code (* for next, # for previous menu)

(10 in first section gives report of A0)

5a. Enter Type of Zone (appears on Zones 2 to 6 only) (* for next, # for previous menu)

0 = EOL Resistors

1 = Normally Closed

2 = Normally Open

5b. Enter Speed of Zone (appears on Zones 1 to 6 only) (* for next, # for previous menu)

0 = 10msec

1 = 350msec (Default)

2 = 700msec

3 = 1.2 seconds

Hardwire Zones advance to step 9, Wireless Zones continue with step 6

6. Enter type of Sensor (* for next, # for previous menu)

2 = Auxiliary Wired (Zone Expander)

3 = Supervised RF (Doors, Motions, Smokes)

4 = Un-Supervised RF (some Panics)

5 = RF Button Type RF (Keyfobs/Panics)

7. Serial Number Programming (* for next, # for previous menu)

Press 1 then enter serial number or trip sensor twice, Loop number will also be learned

This shows ready to learn

Serial and Loop number is manually entered here

or learned by tripping twice (keypad will beep)

(Serial number sticker is on sensor)

8. If "Set to Confirm" was selected while first entering *56 this will appear

Trip sensor again to confirm

If incorrect serial number was learned this will appear

(This can be used to find out a serial number if sticker was removed)

9. This shows summary of new sensor programming (* for next, # for previous menu)

10. Press 0 for next sensor or 1 to enter Alpha descriptions

11. Enter next sensor or 00 to exit * menu

12. Press * or # to exit

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

57 Function Key Programming (6139 or 6160 Alpha Keypad required here)

(If altering function keys A B or C delete programming for zones 95, 99 or 96)

Defaults

Function Key A Zone 95

Function Key B Zone 99

Function Key C Zone 96

Function Key D Single Button Page

1. Press Function Key to program (A = Top to D = Bottom Function Key)

2. Display shows Function Key chosen (* for next, # for previous menu)

3. Choose Function for this Key (* for next, # for previous menu)

00 = A Zone 95 B = Zone 99 C = Zone 96 D = Single Button Page

= Single Button Page (sends 999-9999 message to Pager
= Display Time
= Arm Away
= Arm Stay
= Arm Night/Stay (any Zone in Zone List 5 *81 menu)
= Step Arming (Stay then Night/Stay then Away)
= Device A Activation (Type 66 Function in *80 menu)

08 = Communication Test

09 = Macro Key 1 (Activated by User Code + # + 66)

10 = Macro Key 2 (Activated by User Code + # + 66)

4. Enter next Function Key or 0 to exit

5. Press * or # to exit

58 Expert Programming (faster) (6139 or 6160 Alpha Keypad required here)

1. Press 1 here to allow confirming sensor after serial number input

2. Enter Zone to program (01 to 99) then *

3. Enter Zone Type (Display moves to Report Code, # starts over)

00 = Zone Disabled/Deleted 12 = Monitor Zone (non Burg sends E150)

= Delay Zone 14 = 24 Hr Carbon Monoxide
= Secondary Delay Zone 16 = 24 Hr Fire w/ Verification
= Perimeter/Instant 20 = Arm-Stay (RF only)
= Interior Follower/Motions 21 = Arm-Away (RF only)
= Trouble by Day/Alarm by Night 22 = Disarm (RF only)

To delete Zone enter 00 06 = 24 Hr Silent/Holdup 23 = No Alarm Response

then * until "Delete Sensor" 07 = 24 Hr Police Panic 24 = Silent Burglary

08 = 24 Hr Aux/Medical 77 = Keyswitch Zone

09 = 24 Hr Supervised Fire 90 & 91 = Configurable Zone

10 = Interior with Delay (see locations 182 - 185)

4. Display moves to Report Code, if needed enter 10 (Display moves to Sensor Type, # starts over)

A key moves right through fields if needed

B key moves left through fields if needed

C key copies previous Zone attributes

Hardwired Zones automatically skip to step 9, Wireless Zones continue with step 5

5. Enter Wireless sensor type then *

3 = Supervised RF (Doors, Motions, Smokes)

4 = Un-Supervised RF (some Panics)

5 = RF Button Type RF (Keyfobs/Panics)

6. If Wireless enter Serial Number or trip sensor twice (Keypad will beep twice as Sensor learns)

7. Enter Loop only if manually entering Serial Number (* for next, # for previous menu)

8. If "Set to Confirm" was selected while first entering *58 this will appear

Trip sensor again to confirm

This shows panel and sensor serials match

9. Enter next sensor or 00 to exit

10. Press * or # to exit

59 Exit Alarm Report Code I _ 0 _I
60 Trouble Report Code I _ 1 _I _ 0 _I
61 Bypass Report Code I _ 0 _I _ 0 _I
62 AC Loss Report Code I _ 1 _I _ 0 _I (Randomly sends up to 4 hours after AC failure)
63 Low Bat Report Code I _ 1 _I _ 0 _I
64 Test Report Code I _ 1 _I _ 0 _I
65 Open Report Code I _ 0 _I
66 Away/Stay Report Code I _ 0 _I _ 0 _I
67 RF Xmtr Low Bat Report Code I _ 1 _I _ 0 _I
68 Cancel Report Code I _ 1 _I _ 0 _I
70 Alarm Restore Report Code I _ 0 _I
71 Trouble Restore Report Code I _ 1 _I _ 0 _I
72 Bypass Restore Report Code I _ 0 _I _ 0 _I
73 AC Restore Report Code I _ 1 _I _ 0 _I
74 Low Bat Restore Report Code I _ 0 _I _ 0 _I
75 RF Low Bat Restore Report Code I _ 0 _I _ 0 _I
76 Test Restore Report Code I _ 0 _I _ 0 _I
77 Daylight Savings Start/End Month I _ 4 _I #10_I 00 = Disable 07 = July

= January 08 = August
= February 09 = September
= March #10 = October
= April #11 = November
= May #12 = December
= June

78 Daylight Savings Start/End Weekend I _ 1 _I Start 1 = 1st Weekend

I _ 5 _I End 2 = 2nd Weekend

3 = 3rd Weekend

4 = 4th Weekend

5 = Last Weekend

6 = Next to Last Weekend

= 3rd from Last Weekend

81 Zone Lists for Output Devices

1. Enter Zone List to program (* for next, 00 to exit)

List 1 = General Purpose

List 2 = General Purpose

List 3 = Chime by Zone

List 4 = Cross Zones (see also *85 Cross Zone Timer)

List 5 = Night/Stay Arm (Enter all interior zones that will arm)

List 6 = General Purpose

List 7 = General Purpose

List 8 = General Purpose

List 9 = Zones that activate Pager 1

List 10 = Zones that activate Pager 2

2. Enter Zone(s) to add to Zone List

Enter multiple Zones as 01* 02* 03*, finish with 00

3. Delete Zone List here if needed

Enter multiple Zones as 01* 02* 03*, finish with 00

4. Delete Zone here if needed

Delete multiple Zones as 01* 02* 03*, finish with 00

5. Enter next Zone List to program or 00 to exit

6. Press * or # to exit

82 Custom Alpha Editing

84 Auto Stay Arming I _ 0 _I 0 = Disable

(RF arming overrides this feature) 1 = Enable

85 Cross Zone Timer I _ 0 _I 0 = 15 sec 9 = 5 min

Set 2 zones in *81 Zone List 4 1 = 30 sec # + 10 = 6 min

if both zones activate in this time 3 = 60 sec # + 11 = 7 min

period alarm will be sent. 4 = 90 sec # + 12 = 8 min

5 = 2 min # + 13 = 10 min

If one zone goes into alarm a E380 6 = 2 1/2 min # + 14 = 12 min

trouble will be sent instead 7 = 3 min # + 15 = 15 min

= 4 min

86 Cancel Verify Keypad Display I _ 0 _I 0 = Disable

(Shows CA or CANCEL on display) 1 = Enable

87 Misc Fault Delay Time I _ 0 _I 0 = 15 sec 9 = 5 min

= 30 sec # + 10 = 6 min

3 = 60 sec # + 11 = 7 min

4 = 90 sec # + 12 = 8 min

5 = 2 min # + 13 = 10 min

6 = 2 1/2 min # + 14 = 12 min

7 = 3 min # + 15 = 15 min

8 = 4 min

89 Event Log 80% Full Reporting I _ 0 _I _ 0 _I
90 Event Logging I _ F _I 0 = No Event Logging

(Add together if needed) 1 = Log Alarm/Alarm Restore

2 = Log Trouble/Trouble Restore

4 = Log Bypass/Bypass Restore

8 = Log Open/Close

F = Log All

91 Option Selection I _ 0 _I 0 = None

= AAV 2-Way Enable

8 = Enable Exit Delay Restart

# + 12 = AAV + Exit Delay Restart

92 Phone Monitor Enable I _ 0 _I _ 0 _I 1st Digit

= Disable
to 15# = 1 to 15 min before Alarm
nd Digit

0 = Keypad Display on Phone Fault

= Keypad Display + Sounder
= Keypad Display/Sounder/

Program Output Start

93 Reports per Armed Period I _ 2 _I 0 = Swinger Disable

= 1 Report
= 2 Reports

94 Download Phone (16 digits) I _1 _I _ 8 _I _0 _I _ 0 _I _6 _I _ 8 _I _2 _I _ 1 _I _6 _I _ 9 _I _0 _I _ _I
95 Ring Count I #15_I 00 = Downloading Disable

to 14 = Rings before answer

15 = Answering Machine over-ride

96 Reinitialize Download (Defaults download CSID, resets account number to FFFF)
97 Default Panel (Press 1 after *97 to return panel to default profile 1)
98 Exits Program Mode (Will not allow re-entry with Installer Code + 8 + 0 + 0)
99 Exits Program Mode (Will allow re-entry with Code + 8 + 0 + 0)

Pager Information

Enter Pager number in *160
Enter Pager characteristics in *161 if needed (if Pin Numbers or Access Codes are required)
Enter what pager reports in *162
Enter Pager delay in *172 (Leave at 3 minutes)
If needed disable Pager O/C reports - Master Code + 8 + User + #5 + 0 (by default paging is enabled)
If needed enable "D" Key (bottom Function Key) for 1-button page in *57
If sending Zone Alarms add which Zones will activate pager (01 to 99) to Zone List 9 in *81
Report codes in *65 and *66 are NOT required

160 Pager 1 Phone (20 digits) I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I

End Phone with * # + 11 = * # + 12 = # # + 13 = 2.5 second pause

161 Pager 1 Characteristics (16 digits) I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I
162 Pager 1 Reports I _ 0 _I 0 = No Reports Sent

= Open/Close All Users

4 = All Alarms & Troubles

5 = Alarms/Troubles/Open/Close

# + 12 = Alarms/Troubles in Zone List 9

# + 13 = Alarms/Troubles in Zone List 9

Open/Close for All Users

163 Pager 2 Phone (20 digits) I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I

End Phone with * # + 11 = * # + 12 = # # + 13 = 2.5 second pause

164 Pager 2 Characteristics (16 digits) I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I
165 Pager 2 Reports I _ 0 _I 0 = No Reports Sent

= Open/Close All Users

4 = All Alarms & Troubles

5 = Alarms/Troubles/Open/Close

# + 12 = Alarms/Troubles in Zone List 10

# + 13 = Alarms/Troubles in Zone List 10

Open/Close for All Users

172 Pager Delay Option for Alarms I _ 3 _I 0 = None

1 = 1 minute

2 = 2 minutes

3 = 3 minutes

174 Smoke Detector Clean Me Option I _ 0 _I 0 = Disabled

= Enabled (for certain ESL 2-wire smoke detectors)

177 Device Duration 1, 2 I _ 0 _I 0 = 15 sec 9 = 5 min

(Outputs/Relays) I _ 0 _I 1 = 30 sec # + 10 = 6 min

3 = 60 sec # + 11 = 7 min

4 = 90 sec # + 12 = 8 min

5 = 2 min # + 13 = 10 min

6 = 2 1/2 min # + 14 = 12 min

7 = 3 min # + 15 = 15 min

8 = 4 min

181 50/60 Hz AC Operation I _ 0 _I 0 = 60 Hz

= 50 Hz

182 Configurable Zone Type 90 (10-digits)

I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I

183 Zone Type 90 Report Code

Enter each digit of report code
* scrolls forward 1 digit, # scrolls back back 1 digit
After last digit * exits

Use fields 182 and/or 184 to create a special zone type for *56

Use fields 183 and/or 184 to set a Contact ID report code for alarm and trouble of that zone type

Example: For waterbug sensor enter 8 2 4 #13 4 1 4 0 6 2 in *182 and enter alarm report code of 154, trouble 370 in *183

Many 24 hour zones can use the above programming with different alarm and trouble report codes

184 Configurable Zone Type 91 (10-digits)

I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I _ _I

185 Zone Type 91 Report Code
190 Keypad Address 17 I _ 0 _I _ 0 _I 1st Digit

= Keypad Disabled

191 Keypad Address 18 I _ 0 _I _ 0 _I 1 = Keypad Enabled
192 Keypad Address 19 I _ 0 _I _ 0 _I 2nd Digit

= No Sound Suppression

193 Keypad Address 20 I _ 0 _I _ 0 _I 1 = Suppress Arming & E/E Beeps

= Suppress Chime Beeps only

194 Keypad Address 21 I _ 0 _I _ 0 _I 3 = Suppress Arming & E/E Beeps and Chime Beeps
195 Keypad Address 22 I _ 0 _I _ 0 _I
196 Keypad Address 23 I _ 0 _I _ 0 _I
197 Exit Time Display Interval I _ 2 _I 0 = No Display